Recent content by firey_kimchi

  1. F

    6 speakers on 4 channel amp?

    Sorry, replied to the wrong quote. Should've been to Revelle's original question.
  2. F

    6 speakers on 4 channel amp?

    That will work fine. I have my 4 channel amp (SSA IC150.4) powering 2 sets of SSA Evil 6.5s (front and rear) on channels 3/4 and a pair of SSA Evil 1" tweeters on channels 1/2. It sounds amazing and I'm very happy with it!
  3. F

    COMPLETED SoundSplinter Rl-i, Rl-p, or Orphan 8s

    It's a long shot but I'm looking for some SoundSplinter gear. I used to have 5 Orphan 8s and stupidly sold them a few years back. Let me know what you have...
  4. F

    Clipping Need Advice

    Multiply 450w times 1 (ohm) then square root...21.21v
  5. F

    Zed Audio Minotaur I Repair

    He was the "well-known repair technician/engineer that used to work with Zed" that I sent it to but he couldn't fix it. The continuous popping noise has been fixed after I sent it to someone else for repair but now it has loud static if I use the amp's x-overs.
  6. F

    Zed Audio Minotaur I Repair

    Yes, "Flat" mode bypasses the amp's x-overs. I just got it back from being repaired so I would've hoped it was fully checked out and tested prior to them returning it. I guess I'll just have to use the H/U's x-overs and run it that way.
  7. F

    Zed Audio Minotaur I Repair

    I finally got the popping issue fixed but now there's loud static when I use the amp's crossover (high/low) in "Pre" mode. If I put it in "Flat" mode, there's no static noise. I swapped out RCAs and it still has static. I swapped the amp out with another Minotaur amp and there wasn't any static...
  8. F

    COMPLETED O/S Cerwin Vega (Vega Series) Amps

    Made in U.S.A. goodness...Picked this up at a "second hand" store in Japan. It's practically new! The only thing missing is the remote Vega Bass knob. The bottom cover plate hadn't been removed since it was installed at the factory. The screws were super tough to remove. The guts look amazing...
  9. F

    Zed Audio Minotaur I Repair

    I'd prefer to get it fixed and use it. I have a second, fully functioning Minotaur, and would like to run them together.
  10. F

    Zed Audio Minotaur I Repair

    It's been to him twice and still has had the same issue after getting it back. Long story short, we had a "disagreement" awhile back and he refused to repair anything for me anymore. Then, I sent it to another well-known repair technician/engineer that used to work with him and he couldn't fix...
  11. F

    Zed Audio Minotaur I Repair

    Is there anyone, other than Zed, that can repair these amps? I've sent this amp out 3 different times to get fixed and no one is able to fix it. It always comes back with the same problem...continuous popping sounds after it turns on.
  12. F

    Sundown SAZ 1500d V.3 specs?

    The manual calls for 160A (40A x 4) https://www.manualslib.com/manual/554907/Sundown-Audio-Saz-1500d.html?page=4#manual
  13. F

    COMPLETED O/S Cerwin Vega (Vega Series) Amps

    Bump I know someone has some hidden in their stash
  14. F

    What Brand of Head Unit Do You Have ?

    I've previously used a McIntosh MX-401 and McIntosh MX-406. I'm currently using an Alpine CDA-9887 in my car and plan to use my restored Clarion DRZ-9255 in the wife's car.
  15. F

    Clarion DRZ-9255 or Alpine CDA-9887 for Active?

    I was originally leaning towards the Alpine because I didn't know if the 9255's AUX input for the iPod (3.5mm cable) would be an issue with getting the full RCA 4V output. If I went with the 9255, should I do a 3-way or 4-way? In a 4-way, I'd have the SSA Evil 1 (tweets), Evil 6.5 (mid range)...
Top