voicecoil wiring options

[nVRuckus 5,000+ posts]

chris you gonna run the ZX2500.1 @ .5 ohms? ohh and you need to change the metering to your newest scores with the new box

 

[xterra_on_22s 10+ year member]

that was under the dash but letz see if i can get it on the T.L soon then i'll post it up

 

[Looney_Tune 10+ year member]

ok simple question...didnt want to make another thread. Im getting a D4 sub and want to wire it to 2ohms. There are four sets of terminals...do I only need to use two sets...or do I wire them neg-neg, pos-pos, and then the same to the other two sets?

 

[Looney_Tune 10+ year member]

^^

 

[acold7dusta 10+ year member]

ok simple question...didnt want to make another thread. Im getting a D4 sub and want to wire it to 2ohms. There are four sets of terminals...do I only need to use two sets...or do I wire them neg-neg, pos-pos, and then the same to the other two sets?

only need two, but if you use all 4, itll work, just need more wire

 

[Looney_Tune 10+ year member]

only need two, but if you use all 4, itll work, just need more wire

THANKS

 

[haunther]

what are my options with two DvC2ohm subs

 

[Symon_say 10+ year member]

Hi

I made a box for 4 sub 2 in front and to up, the 2 sub that goes up will be inverted, the subs are 4ohm SVC, do i have to invert the phase of the up subs, and how can i do that,

PS: i need a 4ohm load.

Thanks

 

[gus738 10+ year member]

i have a question guys and i apriciate if you can answer it , i bought 2 kicker L5's 2 ohm's and my eletrionic store put the in the kicker enclosure box , it sounds like the guy knows what he was doing.... but my question should be if the subs are 2 ohms can they be configured to be 4 ohms or other methods???

this is what happend i wanted the 06DS12L5-2 (2 OHM) but the ones they had were the 4 ohm version ( the box tho) so they just took out the 4 ohm subs and put the 2 ohms subs (L5's) but my question is how do i know if the guy pre wired it right????? //content.invisioncic.com/y282845/emoticons/uhoh.gif.c07307dd22ee7e63e22fc8e9c614d1fd.gif//content.invisioncic.com/y282845/emoticons/tongue.gif.6130eb82179565f6db8d26d6001dcd24.gif

 

[937DYTBOI 5,000+ posts]

is it possible to wire 3-DVC 8 ohm subs down to a final load of 4ohms? Im thinking 2- DVC 8 ohm subs can be wired down to 4 ohms. Also what will be all the ohm possibilities for 4-DVC 8 ohm subs

all in all im trying to see how many DVC subs is possible to be ran at 4 ohms as a final load?

thanks

 

[r0ck 10+ year member]

How many different ways to wire 2 - dual 4 ohm ? (the maw12s)

 

[v6camaro00 10+ year member]

if you have 2 dual voice coil 2 ohm subs and wire them to two ohms, wont you only be using one ohm?

 

[got_focus? 10+ year member]

what are my options for 2 - Quad 1's

 

[c_hayhurst 10+ year member]

Lemme get this straight. If I were wire up two, 2Ohm DVC subs like shown in the attached diagram, I will have a 2-Ohm load. I got that.

Here's my question:

If each sub is rated at 1000W RMS, then I could run the subs off one channel on a 2000x1 amp and each sub would get about 1000W each, yes?

Also, are there any concerns about running two, 2Ohm DVCsubs on a .5Ohm load versus a 2Ohm load as a daily driver off one channel (provided the amp is stable at the respective Ohm)?

 

[soda_cube]

so wich option it best for a quad voice coil audiobahn awis12p sub on a 4 channel amp bridged?