Recent content by iSteven

When i run into a situation like this, i like to start over. if you wire in parallel youll be dropping to .5 ohm, if you wire it up in series, youll get 2 ohms. it is a dual voice coil, so you can have this luxury, without requiring another woofer. As i looked up your amplifier, it doesnt say it...

More clarity then bass, iv heard a alpine type r, the new model, on a mb quart ra1500.1, you could get the amp for like 150 on sonic, same with the sub about the same price, amazon you could get it both less then 300. and it was in a sealed box, sounded great. but thats my recommendation, on a...

I Have had a Crunch P1, 5 Channel, i used my subwoofer channel on 2 ohms, and had a regular 4 speakers at 4 ohms on speaker channel, i had no problems with it, its still setup as a audio setup for my work area. I dont think you'll have a problem with it.

I cannot add my profile picture, it adds it but it doesnt show. My pic is 170 by 170 and is under 58 KB. My sub was going to be my profile picture, i like it.

Exactly what the other guy said, impedance through the amplifier will change its RMS output. Finding your final impedance on subs together, then matching ur impedance and wattage with the proper Impedance and wattage on a amplifier.

I see what you mean, to me though that sounds like a volume control for the signal. would it work the same as bass knob. cause im looking to keep same volume just intensify the bass to hit harder.

Could I possibly use the RF 2500BD if I set my gains back? would it risk it?

I know I haven't touched this post in a while. But I would like to save up some money for a Rockford fosgate 2500.1BD. And the birthsheets are showing 3400+ which is amazing. but can an orion handle 3400 watts rms even if its rated 2000 or 2500. Its a big piece of beefy sub, and the talk behind...

How does it work. 4 RCAS, I Could use both runs of rcas and plug them into it. But mine has the phone jack type connection. Do you know where I could find a cable, that changes phone jack on 1 end. other end rcas?

I also would like to see an awnser from someone, who deals a good amount with amplifiers, as I have a Hifonics BRX 1600.1 And I would like to know if these amplifiers give out rated power.

I would like to know how to use 1 bass knob for 2 amplifiers. 2 Amplfiers are running 2 separate subwoofers. How could I use a bass knob on both of those amplfiers but have 1 control ran upfront.

The thing is, it says 2500 watts RMS on the owners manuel that came with it. but I always thought it was 2000 watt. That kind of threw me off and confused me.

Hey, I was going to buy an Orion HCCA 15.2, In the end I thought a 12 inch would be better for me cause I could possibly move it from any car I could have, and a 15 would be struggles in some cars. So I bought Orion HCCA 12.2. It says its the black coil model and its actually 2500 watts. is this...

I do not know much about that amplifier, but some people on here go against getting Hifonics. I have personally seen the Hifonics Brutus BRZ1200.1D Tested with Steve Meades amp dyno. it says 1200 watts at 1 ohm, and it tested out at 1324 watts at 1 ohm at 14 volts. Its on sonic electronics for...

1. Amplifier wattage matching with speaker wattage. 400 watt Speaker 4 ohm single voicecoil, you would look for an amplifier that gives you 400 watts at 4 ohms. lets say you have a 800 watt speaker dual voicecoil 4 ohm, you can wire to 2 ohms or 8 ohms. you could look for an amplifier that gives...