Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Miscellaneous Automotive
Car Electronics & Appearance
2014 Accord Alarm Remote Start Viper 5706V
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="keep_hope_alive" data-source="post: 8332912" data-attributes="member: 576029"><p>I had an issue where the car would start on RS but then shut off after 20 seconds or so. it would then attempt to restart twice (no fire). then it would give up and just tell me "remote start off" on my key fob. it wasn't all of the time but most of the time. it would also sometimes fail to keep the car running in "pit stop mode".</p><p></p><p>you can do diagnostics on the last remote start shutdown (refer to install manual) and it told me low voltage (voltage mode).</p><p></p><p>I did some digging and the solution is in regards to the tach.</p><p></p><p>I had it programmed for virtual tach. it looks at voltage and expects to seen an increase in voltage. but this car regulates voltage at 12.5VDC when the headlights are off (possible ELD). so the car would start and the voltage would be the same and the 5706V thought the car wasn't running. i'm not sure why it failed to restart.</p><p></p><p>I reset the virtual tach.</p><p></p><p>I changed the programming from Virtual Tach to tach.</p><p></p><p>I performed the tach learning procedure.</p><p></p><p>The system confirmed it learned the tach through D2D.</p><p></p><p>car seems to start fine now. all of it makes sense.</p></blockquote><p></p>
[QUOTE="keep_hope_alive, post: 8332912, member: 576029"] I had an issue where the car would start on RS but then shut off after 20 seconds or so. it would then attempt to restart twice (no fire). then it would give up and just tell me "remote start off" on my key fob. it wasn't all of the time but most of the time. it would also sometimes fail to keep the car running in "pit stop mode". you can do diagnostics on the last remote start shutdown (refer to install manual) and it told me low voltage (voltage mode). I did some digging and the solution is in regards to the tach. I had it programmed for virtual tach. it looks at voltage and expects to seen an increase in voltage. but this car regulates voltage at 12.5VDC when the headlights are off (possible ELD). so the car would start and the voltage would be the same and the 5706V thought the car wasn't running. i'm not sure why it failed to restart. I reset the virtual tach. I changed the programming from Virtual Tach to tach. I performed the tach learning procedure. The system confirmed it learned the tach through D2D. car seems to start fine now. all of it makes sense. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Miscellaneous Automotive
Car Electronics & Appearance
2014 Accord Alarm Remote Start Viper 5706V
Top
Menu
Home
Refresh