Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
Cyn's - - - 007 Impala Build Log...
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="cyn" data-source="post: 7856888" data-attributes="member: 635432"><p>Well I finished the box out for the 15" AA a while back... blew the sub.. Redoing my install this month..</p><p></p><p>Going with a Quasi 6th order for an RE HC 2002 12" Sub, Will be ported through the Rear deck.. I've put deadner on the front Doors, Truck Floor and Trunk Lid.</p><p></p><p>So the new install that I will be working on will be as follows:</p><p></p><p>Deaden up the Rear Deck, cut out the port hole for the Box.. Re-run all of my wires from the front to rear separated from each side. Power and ground on the passenger side. All RCA and Speaker wires in the middle and Drive Side, RCA's in the Middle, Wires on the Driver side. Finishing out the Front Doors with the CDT Comps. Making an Amp Rack in the Trunk to put the amps out of the way and route wiring better. Redo my Ground with a Nice Distro Box.. Making a Complete floor with a removable Tire Well hole. Hopefully all out of 1/4" Birch... Same as the Amp Rack but it will be 1/2" recessed into the Wells.. Will be doing more deadner on the trunk floor and lid and the rear bumper"inside the liner of the bumper" This will be a long process as work has taken up a lot of my time lately. But I will update with new pictures sometime this week of the deadening that I have done.. Also I will be getting all of my Stock Electrical Wiring for the Battery and main box wires changed out and upgraded along with the Big 3 before adding in my front stage Amp... Depending on Voltage drops after the Big 3 and the other upgrades to the stock electrical wires i'll Add another battery in the trunk on the other side in the Well.. After all of this is done, I plan on redoing the Rear Deck cover completely. Fiberglass cover with new pods for either 5.25 or 6" comps, also doing a molded out port entrance for the sub.. I'll see how that goes when I get to that point..</p><p></p><p>Depending on how long this takes and if I follow through with it all this will stay in for a while... Box might change later on depending on what setup I go with.. If this stays for 6months I'll be happy with it.. Also depending on me getting another SUV for doing a huge build this will completely change to a basic setup with a smaller box.. fully clean hidden install.</p></blockquote><p></p>
[QUOTE="cyn, post: 7856888, member: 635432"] Well I finished the box out for the 15" AA a while back... blew the sub.. Redoing my install this month.. Going with a Quasi 6th order for an RE HC 2002 12" Sub, Will be ported through the Rear deck.. I've put deadner on the front Doors, Truck Floor and Trunk Lid. So the new install that I will be working on will be as follows: Deaden up the Rear Deck, cut out the port hole for the Box.. Re-run all of my wires from the front to rear separated from each side. Power and ground on the passenger side. All RCA and Speaker wires in the middle and Drive Side, RCA's in the Middle, Wires on the Driver side. Finishing out the Front Doors with the CDT Comps. Making an Amp Rack in the Trunk to put the amps out of the way and route wiring better. Redo my Ground with a Nice Distro Box.. Making a Complete floor with a removable Tire Well hole. Hopefully all out of 1/4" Birch... Same as the Amp Rack but it will be 1/2" recessed into the Wells.. Will be doing more deadner on the trunk floor and lid and the rear bumper"inside the liner of the bumper" This will be a long process as work has taken up a lot of my time lately. But I will update with new pictures sometime this week of the deadening that I have done.. Also I will be getting all of my Stock Electrical Wiring for the Battery and main box wires changed out and upgraded along with the Big 3 before adding in my front stage Amp... Depending on Voltage drops after the Big 3 and the other upgrades to the stock electrical wires i'll Add another battery in the trunk on the other side in the Well.. After all of this is done, I plan on redoing the Rear Deck cover completely. Fiberglass cover with new pods for either 5.25 or 6" comps, also doing a molded out port entrance for the sub.. I'll see how that goes when I get to that point.. Depending on how long this takes and if I follow through with it all this will stay in for a while... Box might change later on depending on what setup I go with.. If this stays for 6months I'll be happy with it.. Also depending on me getting another SUV for doing a huge build this will completely change to a basic setup with a smaller box.. fully clean hidden install. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
Cyn's - - - 007 Impala Build Log...
Top
Menu
Home
Refresh