Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Speakers
Speaker help.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="kouger" data-source="post: 8855511" data-attributes="member: 689597"><p>So from what I can tell, the driver and the tweeter are connected together. The cap is inline with the tweeter.</p><p>The cap has a marking on it 3.3 uF. 63WV</p><p>When I put my meter on across the cap I get 8 ohms</p><p>When I test across the tweeter connectors I get I get 6.2 ohms</p><p>When I test across the driver / cone I get 2 ohms</p><p>When I test across the pins for the speaker wires I get 2 ohms</p><p></p><p>Now I just bought the JBL GX328. This is the spec from their website:</p><p>Power Handling: 25Wrms, 75W Peak Frequency Response: 90Hz – 21kHz Impedance: 2.3 ohms Sensitivity (@ 2.83V/m): 89dB</p><p>When I test across the pins for the speaker wires I get 2.4 ohms.</p><p></p><p>There is a cap on the JBL GX328 with the marking of 3.9 uF. 5 0 V.</p><p>One side of the cap is connected to the smaller of the two pins and the other is running under the sticker on the magnet and goes inside somewhere - can't see it.</p><p></p><p>So I connected up the GX328's and I did notice that the volume is slightly lower on the GX328 than the original speakers.</p><p>The other thing that was a big difference is that the GX328's have more bass and what seems to me like less mid.</p><p>The high pitch sounds (like cymbals of a drum) are much clearer and more prevalent.</p><p>The original speakers seem to have much more mid than the GX328 - could this be because of the capacitors.</p><p></p><p>Would removing the capacitor from the GX328 cause any damage to the speaker - or swapping them with the original speakers capacitors make any difference.</p><p>I would prefer to get more mids out of the new GX328 - I don't care if there is more base from them as it seems sound better in the car - just not crazy about the low mids.</p><p></p><p>One thing I am happy about is that there is no distortion when a call comes in.</p><p>Oh, I also bought the JBL GX428 and will probably swap that out with the center one.</p><p>GX428 4" coaxial car audio loudspeaker Power Handling: 35Wrms, 105W Peak Frequency Response: 75Hz – 21kHz Impedance: 2.3 ohms Sensitivity (@ 2.83V/m): 90dB</p><p></p><p>Any idea what the cap on the GX328's is for?</p><p>Thanks for your help.</p><p></p><p>Thanks again for your help.</p></blockquote><p></p>
[QUOTE="kouger, post: 8855511, member: 689597"] So from what I can tell, the driver and the tweeter are connected together. The cap is inline with the tweeter. The cap has a marking on it 3.3 uF. 63WV When I put my meter on across the cap I get 8 ohms When I test across the tweeter connectors I get I get 6.2 ohms When I test across the driver / cone I get 2 ohms When I test across the pins for the speaker wires I get 2 ohms Now I just bought the JBL GX328. This is the spec from their website: Power Handling: 25Wrms, 75W Peak Frequency Response: 90Hz – 21kHz Impedance: 2.3 ohms Sensitivity (@ 2.83V/m): 89dB When I test across the pins for the speaker wires I get 2.4 ohms. There is a cap on the JBL GX328 with the marking of 3.9 uF. 5 0 V. One side of the cap is connected to the smaller of the two pins and the other is running under the sticker on the magnet and goes inside somewhere - can't see it. So I connected up the GX328's and I did notice that the volume is slightly lower on the GX328 than the original speakers. The other thing that was a big difference is that the GX328's have more bass and what seems to me like less mid. The high pitch sounds (like cymbals of a drum) are much clearer and more prevalent. The original speakers seem to have much more mid than the GX328 - could this be because of the capacitors. Would removing the capacitor from the GX328 cause any damage to the speaker - or swapping them with the original speakers capacitors make any difference. I would prefer to get more mids out of the new GX328 - I don't care if there is more base from them as it seems sound better in the car - just not crazy about the low mids. One thing I am happy about is that there is no distortion when a call comes in. Oh, I also bought the JBL GX428 and will probably swap that out with the center one. GX428 4" coaxial car audio loudspeaker Power Handling: 35Wrms, 105W Peak Frequency Response: 75Hz – 21kHz Impedance: 2.3 ohms Sensitivity (@ 2.83V/m): 90dB Any idea what the cap on the GX328's is for? Thanks for your help. Thanks again for your help. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Speakers
Speaker help.
Top
Menu
Home
Refresh